See how the YiliJet DREAMS 1224 One Pass UV printer produces decorative MDF boards in a continuous production test. Explore 17-second print cycles, 100 accepted boards per hour during a four-hour test, ink consumption and print quality results.
MDF Board Printing Machine | DREAMS 1224 One Pass UV | YiliJet
Case Details
MDF Printing
High-Speed One Pass UV Printing on MDF Boards
MDF (medium-density fibreboard) is widely used in furniture components, decorative wall panels, cabinetry and interior fit-outs, where manufacturers require printing workflows with consistent visual results, flexible digital design capability and stable production performance. The YiliJet DREAMS 1224 One Pass UV printing system has undergone testing on 1220 × 2440 × 18 mm MDF boards under 720 × 1800 print mode: a walnut woodgrain pattern was printed in a 17-second cycle per board, and the unit successfully ran a 4-hour continuous production test at a throughput of 100 boards per hour. Note that actual performance will vary based on artwork, substrate surface condition, ink setup, print parameters, loading/unloading method and on-site production environment.
DREAMS 1224 MDF Printing Test
Print Cycle
17 seconds
Reported for the tested walnut woodgrain design.
Production Output
100 boards/hour
Reported continuous production rate during the four-hour test.
Test Duration
4 hours
Reported continuous production test.
Ink Consumption
10–12 ml/m²
Reported test range; actual use depends on artwork and print settings.
Test substrate: MDF · Board size: 1220 × 2440 mm · Thickness: 18 mm · Reported print mode: 720 × 1800.
Important distinction: 17 seconds is the reported printing cycle for the tested design; 100 boards/hour is the reported continuous production rate. These are different measures.
Print Quality & Production Results
Image Consistency
The reported test showed very good image consistency and minimal visible color variation.
Reduced Banding
Banding was reported to be substantially reduced compared with the reported baseline process.
Adhesion Evaluation
Adhesion was reported as normal under the test conditions. Additional post-curing may be evaluated where appropriate.
DREAMS 1224 MDF Production Test
Walnut Woodgrain & Marble-Effect Printing
Printer
DREAMS 1224
Substrate
MDF
1220 × 2440 × 18 mm
Test Artwork
Walnut Woodgrain & Marble Effect
Print Mode
720 × 1800
Metric
Reported Result
Walnut woodgrain print cycle
17 seconds per board
Continuous production rate
100 boards/hour
Continuous test duration
4 hours
Ink consumption
10–12 ml/m²
Adhesion
Reported as normal
Color consistency
Very good; minimal visible color variation
Banding
Substantially reduced versus reported baseline
Production speed comparison
Reported improvement of nearly 8×
The nearly 8× speed comparison should be supported by documented baseline equipment, artwork, operating conditions and production-rate calculations. The reported test indicates that DREAMS 1224 can support high-throughput digital printing on the tested MDF configuration, with very good image consistency and reduced visible banding.
MDF Printing Applications
Decorative Wall Panels
Furniture & Cabinet Components
Marble-Effect Panels
Customized Decorative Boards
Potential applications also include interior fit-out panels and customized digital decorative panels. MDF grades and surface finishes vary; results from the tested MDF should not automatically be applied to every MDF surface or other board material.
MDF Printing Cost Evaluation
Full Board Area
2.9768 m²
Calculated from 1.22 m × 2.44 m.
Estimated Ink per Board
29.77–35.72 ml
Calculated from the reported 10–12 ml/m².
Cost Components
Ink
Ink consumed per board × ink price per ml.
Energy
Measured kWh per board × electricity price per kWh.
Labor
Allocated labor cost divided by accepted boards produced.
Maintenance & Waste
Include actual maintenance and waste costs where reliable figures are available.
The production cost model should use accepted boards, rather than theoretical output, as the production denominator. Facility cost can also be allocated per accepted board where reliable figures are available.
MDF Printing FAQ
1. How fast can the DREAMS 1224 print MDF boards?
In the reported test on 1220 × 2440 × 18 mm MDF, the walnut woodgrain design had a 17-second single-board print cycle. The reported continuous production rate was 100 boards per hour during a four-hour test. These figures describe different stages of production and should be evaluated separately.
2. What is the ink consumption for MDF printing?
The reported consumption was 10–12 ml/m². For a 1220 × 2440 mm board, this corresponds to approximately 29.77–35.72 ml per board, assuming the reported consumption range applies to the tested image and the full board area.
3. Is the printed image consistent across MDF boards?
The reported test showed very good image consistency and minimal visible color variation. Production approval should still use agreed color tolerances and inspection procedures.
4. Can One Pass UV printing reduce banding?
In the reported comparison, banding was substantially reduced. The magnitude of improvement should be supported with comparable images and documented test conditions before being expressed as a numerical claim.
5. Does MDF printing require post-curing?
The reported adhesion result was normal under the test conditions. Additional post-curing may be evaluated to improve adhesion. The appropriate curing method and acceptance criteria should be established through testing on the actual MDF surface and intended end use.
6. Can the same results be expected on other board materials?
Not automatically. MDF grades and surface finishes vary. Other board materials require separate testing for adhesion, curing, print quality and production performance.
Test Your MDF Boards with DREAMS 1224
Share your MDF board dimensions, surface finish, artwork and production targets to evaluate printing performance under an agreed test protocol.